Pressure usually positive mmlig inHg. Pressure usually negative w. Watt liters US qt, imp qt.. When the vehicle is to be equipped with a mobile two-way radio, observe the fotlowing precautions: I.
Install the antenna at the farthest point from control units. Install the antenna feeder as far as possible from the control unit harnesses at Ieast 30 cm Ill. Ensure that the antenna and feeder are properly adjusted. The key should now be free for removal. The two lead wires should be connected to probes.
The test light is used for simple voltage checks and for checking for short circuits. Caution l When checking over 3. Caution l Do not connect , line to a body other damage ponents. Caution l Do not insert the jumper nosis connector terminal, terminal. When a tester is used to check for continuity or to measure voltage, insert the tester probe from the wire harness side.
Check the terminals of waterproof connectors from the connector side, as they cannot be accessed from the wire harness side. Caution l Use fine wire to prevent damage to the terminal. When installing the terminal, be sure to insert it until it locks securely. Insert a thin piece of metal from the terminal side of the connector, and then, with the terminal locking tab pressed down, pull the terminal out from the connector. Same as the female type, Sensors, Switches, and Relays Handle sensors, switches, and relays carefully.
When replacing a fuse, be sure to replace it with one of specified capacity. If a fuse again fails after it has been reptaced, the circuit probably has a short circuit and the wiring should be checked. Be sure the negative battery terminal i ; disconnected fore replacing a main fuse A.
When replacing a pullout in the fuse box cover. The first letter indicates the base color of the wire and the second the color of the stripe.
If there has been continuous hard driving, mountain driving, or if the brakes are used extensively or the vehicle is operated in extremely humid climates, the brake fluid shotlid be changed annually. Emission Control and Related Systems The ignition and fuel systems are vitally important to the proper operation system, as well as for efficient engine operation. It is strongly recommended systems be done by your Authorised Mazda Dealer.
Lubrication service based on distance only, 10, km 6, miles , not time. Failure to replace the timing belt may result in damage to the engine. Lubrication service based on distance only 10, km 6, miles not time. If there has been continuous hard driving, mountain driving, or if the brakes are used extensively or the vehicle is operated in extremely humid climates, the brake fluid should be changed annually. Emission Control and Related Systems The ignition and fuel systems are vitally important to the proper operation of the emission control and related system, as well as for efficient engine operation.
It is strongly recommended that all servicing related to these systems be done by your Authorised Mazda Dealer. Bl6 Bf6 6. Engine Removal.. Refer to Sections Ff and G. Symbols: 9. Interchangeable Crankshaft related Timing related belt Valve retated Lubrication system related [ Cyirnder head i Camshaft oil sea! Disconnect the negative battery cable. Drain the engine coolant and transaxle oil. Remove in the order shown in the figure, referring Step t to Removal Note.
Undercovers 2. Side covers 3. Resonance chamber and air cleaner 4. Battery bracket, cover and bafiery 5. Battery carrier and battery duct 6. Accelerator cable 7. Radiator hose 8. Coolant reservoir hose 9. Cooling fan connector IO. Radiator switch connector ATX 1 f. Position wire. Remove the AC compressor with the hoses still connected. Position the compressor away from the engine and secure it with wire. Step 2 1. Disconnect the harness connectors shown in the figure.
Disconnect the hoses shown in the figure. Brake vacuum 2. Fuel hose 3. Vacuum hose Purge control [except ECE without catalyst] 4. Heater hose hose Removal Note OWOBX the fuel hoses. Disconnect Heater hose Caution l Do not lose the heater when removed.
Depress hose. Select and shift cable MTX 3. Shift control cable ATX 4. Front exhaust pipe 5. Stabilizer 6. Tie-rod end below Removal Note ,, Driveshaft Removal Note. Propeller shaft Removal Note. Remove the cotter pin and loosen the nut until it is flush with the end of the ball joint stud. Separate the cotter pin. Remove the joint shaft 2. Remove the lower I 93EOB arm ball joint clinch bolt. Pry the lower arm downward to separate it from the knuckle.
Separate 03UOBX damage the oil seal. Exhaust manifold insulator and gasket 3. Water inlet pipe and gasket 4, Engine mount member Removal Note.. Clutch 2. Dynamic page BY damper 8. Engine and transaxle assembly Removal Note. Suspend member the engine with a chain hoist. Remove the No. Remove the engine mount member bolts and nuts and the engine mount member.
Clutch release cylinder MTX f. Remove the release cylinder pipe bracket from the transaxle. Position the release cylinder with the hose connected away from the transaxle for easier removal. Remove 93GOBl Bl the pipe and hose. Center differential lock motor Removal Note. Starter and bracket 4. Throttle cable 23 5. Tighten all bolts and nuts to the specified Step torques. I the engine 1. Join Toraue 1- - and transaxle. Snecifications -r-- MTX 3. Specifications 5.
I flO 7. Install the engine assembly any components and transaxle in the engine assembly. Install the No. Install the clutch U-y. Align the engine mount member to the No.
Install and tighten the engine mount member bolt and nuts. Tightening 7. Tighten ,. Tighten 1 A-I-X bolts in two or three steps in the order shown. Tightening 9. Tighten torque: N-m 4. Tightening IO. Tighten m-kg, torque: N-m 6. Tighten torque: Nom 7,f0,5 torque: N-m 6. Install the dynamic Tightening W Remove ft-lb nut. Tightening 43GOBlt m-kg, m-kg, ft-lb m-kg, ft-Ib damper. Step 3 Torque Specifications 6. Install the propeller shaft. Refer to page l Driveshaft I. Apply grease to the end of the driveshafi.
Caution l When installing the driveshaft, be careful not to damage the transaxle oil seal. Install the driveshaft along with a new clip. Tightening torque: Nm 4.
Install the joint shaft. Tighten the bolts in the order shown. Tightening torque: Nom 4. InstaIl the tie-rod Tightening end to the knuckle. Install a new cotter i m-kg, ft-lb pin. Dimension Tightening A: imm torque: Nm l Instail the exhaust pipe along with a new gasket; tighten locknuts. Loosely tighten bracket nuts 3.
Tighten locknuts 0. Tightening 3f -- 4. Tighten Tightening then loosely torque: N-m 3. Install the shift cable and the spring pin. D Shift control cable ATX 1. Install the shift control cable Tightening torque: 6. Connect the hoses shown Caution l Position the hose clamp pliers to ensure a good Step 5 1.
Connect the harness in the figure. TIAI -. I I -4 m-m. Tightening torque: Nm 9. Tightening torque: N-m 2. Tightening torque: m-kg, N-m 3. Adjust the drive belt deflections. Refer to page 93GOE ; Radiator f. Install fan assembly and cooling fan assembly. Tightening torque: 7.
Connect 3. Connect 4. Connect 5. Connect 6. Connect 7. ATX coolant reservoir hose. Install the accelerator cable. Install the battery carrier. Install 4. Install the air cleaner assembly. Tightening torque : Nm I Connect the airflow sensor Resonance chamber 1. Steps after installation 1.
If the engine oil was drained, refill with the specified amount and type of engine oil. Fill the radiator with the specified amount and type of engine coolant. Fill the transaxle with the specified amount and type of transaxle oil. Refer to pages J, 4. Connect the negative battery cable. Start the engine and check the following: 1 Engine oil, transaxle oil, and engine coolant leakage 2 Ignition timing and idle speed 3 Operation of emission control system 6. Perform a road test.
Recheck the engine oil and engine coolant levels. Engine stand mounting. Engine stand dismounting. Symbols: 5.
Not Interchangeable name 1 Cylinder head Camshaft oil sea! The identification mark is cast at the rear of the cyfinder head. But in conjunction with the newly provided Mxication oil passages on the cylinder block are used. Tfie oil pan has a provision for oil to return from the turbocharger. Ignition system Refer to Section G. Compression 3. Fuel system Refer to Section F3. Verify that the battery is fully charged. Recharge it if necessary. Warm up the engine to normal operating temperature.
Turn the engine OFF. Remove all of the spark plugs. Disconnect the ignition coil connector. Connect a compression gauge to the No. Fully depress the accelerator pedal and crank the engine. Record the maximum gauge reading.
Check each cylinder in the same manner. Compression: 1, kPa IO. D 93G IO. If the compression in one or more cylinders is low, pour a small amount of engine oil into the cylinder and recheck the compression. Connect the ignition coit connector. Apply antiseize compound or molybdenum-based lubricant to the spark plug threads.
Install the spark plugs. Tightening torque: N-m 1. Refer to Section FZ. Remove in the order shown in the figure, referring Step 1. Radiator bracket Radiator and coofing fan assembly Battery duct Air pipe and air bypass valve Intercooler and air pipe Removat Note. Air pipe and gasket Remove figure.
Loosen hose 4. Remove band. Remove the intercooler bracket shown in the and air pipe downward. Caution l Cover the hose with a rag because fuel will spray out when disconnecting. Disconnect Heater the fuel hoses. Driveshafts cable Removal Note. Propeiler shaft Removal Note. Select and shift cables 3. Front exhaust pipe 4. Stabilizer 5. Tie-rod end Removal Note. Remove the cotier pin and loosen the nut until it is flush with the end of the ball joint stud. Caution Do not l 2.
Separate reuse the cotter pin. Driveshaft 1. Remove the joint shaft. Remove the lower arm bali joint clinch 93ECB c bolt. Caution Do not damage l the ball joint 3. Pry the lower arm downward dust boot. Caution l Do not damage 4. Separate 1 03tiOBX Bz-t6 the the driveshafi oil seat. Alternator and drive belt 8. I ntercooler brat kets 9. Engine mount member Removal Note. Dynamic damper Removal Engine note mount 1.
Remove the engine mount engine mount mem her. Caution l Do not damage the pipe and hose. Intake manifold bracket 2. Starter and bracket 3. Transaxie 4. Remove in the order shown ir! Exhaust 2. Exhaust 3. Exhaust manifold manifold manifold insulator and turbocharger gasket 4.
Water assembly bypass pipe 5. Remove the engine from the SST engine stand. Remove the SST engine hanger from the engine.
Install the parts shown in the figure. Tighten the parts to the specified torques. Remove ail foreign material from the water inlet pipe mounting surfaces. Install a new gasket and the water inlet pipe. Tightening f torque: Nm 1. Apply a small amount of engine 2. InstaIi the water bypass pipe. Install a new gasket. Instatl the exhaust manifold and turbocharger assembly. Tightening 4. Connect block. Exhaust Manifold Insulator 1.
Install the exhaust manifold Tightening 7. Connect insulator. Step 1 I. Connect Torque the engine and transaxie. Specifications M 6. Specifications S 5. Install the engine 93G B N-m assembly any camponents and transaxle in the engine assembly. Monut the alternator to the engine. Tightening torque : J: m-kg, N-m 1. Install the drive belt. Refer to page ft-lb ft-lb Z Engine mount, clutch release cylinder member 1.
Tightening torque : Nm [I. Tightening torque: N-m Tighten the No. Tighten m-kg, engine m-kg, Mb mount nuts. Tightening torque: N-m 6. Tighten No. Install engine Mazda Workshop Manuals Supplement. This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Read More. Likes Followers Followers Followers. Your country's customs office can offer more details, or visit eBay's page on international trade. Located in:.
This amount is subject to change until you make payment. For additional information, see the Global Shipping Program terms and conditions - opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fees. For additional information, see the Global Shipping Program terms and conditions - opens in a new window or tab.
Estimated between Tue. Estimated delivery dates - opens in a new window or tab include seller's handling time, origin ZIP Code, destination ZIP Code and time of acceptance and will depend on shipping service selected and receipt of cleared payment - opens in a new window or tab. Delivery times may vary, especially during peak periods. Ships today if paid within 8 hrs 44 mins Details. Please allow additional time if international delivery is subject to customs processing.
Seller does not accept returns See details. Any international shipping and import charges are paid in part to Pitney Bowes Inc. Learn More - opens in a new window or tab International shipping and import charges paid to Pitney Bowes Inc. Learn More - opens in a new window or tab Any international shipping and import charges are paid in part to Pitney Bowes Inc.
Learn More - opens in a new window or tab Any international shipping is paid in part to Pitney Bowes Inc. Learn More - opens in a new window or tab. Related sponsored items. Showing Slide 1 of 3. New New New. Seller Pre-owned Pre-owned Pre-owned. Report item - opens in a new window or tab.
Seller assumes all responsibility for this listing. Item specifics. Year of Publication:. Media Type:. Literature Type:.
0コメント